the last usb device you connected to this computer malfunctioned

528
the last usb device you connected to this computer malfunctioned

Here we can see “the last USB device you connected to this computer malfunctioned”

When Windows fails to acknowledge a USB device that has been connected to the pc, it spits out a mistake message that states:

The only thing which will be inferred from this error message is that the USB device the user suffering from this problem last connected to their computer has, in a method or another, malfunctioned and isn’t working love it is meant to. This problem renders whatever USB device it affects unusable, and not having the ability to use a USB device connected to your computer is most certainly a big problem.

This issue isn’t sure to a selected version of the Windows OS and has been known to affect users of all currently supported versions of Windows. This problem certainly is the head-scratcher, but that does mean that it can’t be fixed. the subsequent are a number of the foremost effective solutions that any Windows user suffering from this problem can use to undertake and obtain prevent this problem and successfully use the affected USB device:

Also See:  telegram delete account

Solution 1: Disconnect then reconnect the affected USB device several times

First and foremost, the only possible solution to the present problem would be to disconnect the USB device you’re facing this problem with from your computer then reconnect it. In many cases, the “The last USB device you connected to the present computer malfunctioned” error message is simply temporary, and disconnecting then reconnecting the affected USB device several times get to prevent the error message and gets the USB device to interface with and work with the affected computer successfully. Getting this solution to figure might take several tries, so make certain to disconnect then reconnect the affected USB device a minimum of a dozen times.

Solution 2: Power cycle your computer

  1. Remove the affected USB device from your computer.
  2. Turn your computer off.
  3. Unplug the facility supply cord from your computer.
  4. Wait for approximately 2 minutes – this is often enough time for any and every one residual charge present on the pc and its hardware to dissipate.
  5. Plug the facility supply cord back into the pc.
  6. Boot your computer up.
  7. When the pc boots up, reconnect the affected USB device and check to ascertain whether or not the matter has been resolved.

Solution 3: Disable USB selective suspension.

USB selective suspend may be a feature built-in to the Windows OS and enabled by default. However, in some cases, the USB selective suspend setting can cause USB devices to malfunction and not be successfully recognized by Windows, which is why disabling this feature is a superb course of action if you’re experiencing this problem. To disable the USB selective suspend feature, you would like to:

  1. Open the beginning Menu.
  2. Search for “power options. “
  3. Click on the search result titled Power Options.
  4. Click on Change plan settings next to the facility plan that’s currently active on your computer.
  5. Click on Change advanced power settings.
  6. Double-click on the USB settings section to expand it.
  7. Click on the USB selective suspend sub-section to expand it.
  8. Change the setting to Disabled in however many instances of the setting there are under the USB select suspend sub-section (there are often two instances – On battery and Plugged in – within the case of laptops, for example).
  9. Click on Apply, then on OKOK.
  10. Click on Save changes.
  11. Would you please restart your computer and check to ascertain whether or not the matter persists when it boots up?

Solution 4: Disable then re-enable the Generic USB Hub device

  1. Press the Windows logo key + R to open a Run dialogue.
  2. Type devmgmt.msc into the Run dialogue and press Enter to open the Device Manager.
  3. In the Device Manager, double-click on the Universal Serial Bus controllers section to expand it.
  4. Locate and right-click on the Generic USB Hub device
  5. Click on Disable. You ought to be freed from the “The last USB device you connected to the present computer malfunctioned” error message as soon as this device is disabled.
  6. Right-click on the Generic USB Hub device once more and click on Enable.
Also See:  How to Open Task Manager in Windows 11

Solution 5: Update the drivers for all of your computer’s Universal Serial Bus controllers

  1. Press the Windows logo key + R to open a Run dialogue.
  2. Type devmgmt.msc into the Run dialogue and press Enter to open the Device Manager.
  3. In the Device Manager, double-click on the Universal Serial Bus controllers section to expand it.
  4. Right-click on the first device listed under the Universal Serial Bus controllers section and click on Update Driver Software….
  5. Click on Search automatically for updated driver software.
  6. Wait for Windows to automatically look for available updates for the affected hardware device’s drivers.
  7. If Windows finds any available updated driver software, it’ll automatically download and install it, and everyone you’ll need to do is wait for it to try to do so.
  8. Repeat steps 4–7 for every single device listed under the Universal Serial Bus controllers section in your computer’s Device Manager.

Solution 6: Uninstall then reinstall all of your computer’s Universal Serial Bus controllers

  1. Press the Windows logo key + R to open a Run dialogue.
  2. Type devmgmt.msc into the Run dialogue and press Enter to open the Device Manager.
  3. In the Device Manager, double-click on the Universal Serial Bus controllers section to expand it.
  4. Right-click on the very first device listed under the Universal Serial Bus controllers section and click on Uninstall.
  5. Click on OK.
  6. Repeat steps 4 and 5 for every single other device listed under the Universal Serial Bus controllers section.
  7. Once the drivers are uninstalled, close the Device Manager and restart your computer.
  8. When the pc boots up, Windows will automatically detect and reinstall all of the devices you uninstalled.
  9. Once all of the uninstalled devices are reinstalled, check to ascertain if the difficulty has been fixed.

User Questions:

1. The last USB device you connected to the present computer has malfunctioned, and windows don’t recognize it

I have tried repeatedly to repair this issue, and that I cannot find the right answer. I even have searched the online, YouTube, threads, and zip have fixed my issue. I even have a USB port with the error “Windows has stopped this device because it’s reported problems (code 43). An invitation for the USB device descriptor fails, or port reset failed. There’s a yellow exclamation mark beside the USB in the device manager. I even have uninstalled, reinstalled it, checked all USB controllers to make sure they’re all OKOK, and updated all the drivers, and that I still cannot get this port to figure. The cable to the device works on all other computers and devices. The cable is for my phone to transfer files and back up my phone to Kies Air in Windows 10. I even have used different cables, and that I still get an equivalent result. Please help. 

2. The last USB device you connected to the present computer malfunctioned

So annoyed with this. I do not know which device it’s because I have never connected anything recently. 🙁

It’s also making the noise once you connect something every. Damn. Time. What am I able to do to repair it?

3. USB device not recognized. The last USB device you connected to the present computer malfunctioned, and Windows doesn’t recognize it.”

I’m having an issue connecting to my ortur laser 15W. So I buy the subsequent message:

“USB device not recognized, The last USB device you connected to the present computer malfunctioned, and Windows doesn’t recognize it.”

I’ve uninstalled the drivers and installed them again (VCP_V1.5.0_Win10_Win8_64bits) since I even have a WIN 10 with no luck.

After the installation, there’s no new device in the device manager. So I’ve manually entered → Device manager → Action → Add legacy hardware → adv option → Ports(COM & LPT) → Selected STMicroelectronics and Model STMicroelectronics Virtual COM Port (the just one available).

After doing this, I buy a replacement one installed under Ports (COM & LPT) → STMicroelectronics Virtual COM Port (COM7), but it’s the subsequent error:

This device cannot start. (Code 10).

The specified request isn’t a legitimate operation for the target device.“.

I’ve tried with the supplied cable and another one (5m long, worked with this all the time, no issues).

Also tried on two laptops and one desktop, all running on WIN 10 and having an equivalent problem.

Also See:  After a recent patch, New World Gets Review Bombed on Steam

4. USB Not Recognized, The last USB device you connected to the present computer malfunctioned, and…

So I used to be using my windows 10 home laptop this afternoon, and that I was using a mouse, and suddenly it began to acting up just like the response delays once I click a button in the mouse. So I removed the USB plug of the mouse and entered again. But the USB-connected effect was playing, again and again. Then a message popped up saying [USB Not Recognized, The last USB device you connected to the present computer malfunctioned, and windows don’t recognize it]

5. USB Device Not Recognized Issues

I’m new to this forum and am trying to repair a recent problem driving me crazy.

I have an HP Windows 10 PC, and after the pc has been on for a short time, all the USB drives within the back of the PC will fail. So I buy a window that says “USB Device Not Recognized. The last USB Device you connected to your computer malfunctioned and windows don’t recognize it.”

When I reboot the pc, all is OK, and the things I sent to the printer will now print (I have my printer and external hard drives all plugged into the USB drives within the back of the PC).

I have also tried uninstalling updating the drivers, but I’m still having an equivalent issue, and it’s driving me crazy. I’m not an expert with the pc, but I used to be ready to view my error logs and see this.