Can’t Connect to Internet After Installing Windows 10 Creators Update

Here we can see, “Can’t Connect to Internet After Installing Windows 10 Creators Update”

It’s that time of year once more! The Creators Upgrade, Microsoft’s third major update for Windows 10, was recently published. The latest version includes several new features and system enhancements intended primarily for Windows 10 creative users.

However, it appears that, in addition to the new features, early users of the Creators Update may have to contend with specific difficulties. An internet connection issue was one of the first Creators Update complaints.

If you’re having the same problem, keep reading because we’ve compiled a list of probable remedies for you.

How to resolve connection issues in Windows 10 Creators Update

A router or modem usually causes connection problems. So, let’s attempt these steps to see if we can solve the problem: Before starting with the device, let’s rule out any external factors.

1. Turn off your modem or router. Could you wait a minute before turning it on?
2. Instead of using a wireless connection, try using a cable one. Check for changes by plugging in your LAN wire.
3. Temporarily disable the modem/built-in router’s firewall.
4. If you’re using a router, make sure any walls aren’t blocking your signal. Also, avoid placing it near another device that could interfere with the transmission.
5. Restore factory settings to the modem/router.
6. Disable WPS (Wi-Fi Protected Setup) on the router and connect using conventional procedures.
7. Examine the cords to ensure that everything is in working order. If you’re unsure how to do it, look for help online.
8. Make sure your router or modem isn’t overheated. It should be kept away from heat sources.

Let’s get down to system-level workarounds now.

2. Use the Troubleshooter for Internet Connections

Even with Troubleshooting, Microsoft got creative with the Creators Update. As a result, you’ll be able to use a single troubleshooting page to address various issues. One of these is the Internet Connection Troubleshooter, which can be used to troubleshoot connection problems. This is how to put it to use.

1. To open Settings, press Windows key + I.
2. Update & Security are both open.
3. To troubleshoot, go to Troubleshoot.
4. Select Internet Connection Troubleshooter from the drop-down menu.
5. Wait for the procedure to complete and see whether your problems have been resolved.

This appears to be a worthwhile addition. You’ll be able to access individual tools thanks to the consolidated troubleshooting page quickly.

3. Install the latest network drivers

The router may work as intended, but you’ll almost surely have connectivity problems if you don’t have the right drivers. Forced driver updates are known to cause update difficulties in Windows 10.

The ‘auto-updating drivers’ feature, for example, is meant to be a helpful innovation, but it frequently causes a slew of issues with various devices. And in this scenario, network adapters are involved. So, let’s have a look at drivers before moving on to the workarounds:

1. Open the Device Manager by right-clicking Start.
2. Network Adapters should be found.
3. Select ‘Update driver software’ from the context menu of your network adapters. Ensure that both LAN and WLAN adapters are used.
4. Restart your computer after the procedure is completed and attempt connecting again.
5. If the problem still persists, return to Device Manager > Network Adapters.
6. Open Properties by right-clicking the network adapter.
7. Uninstall the driver from the Driver tab.
8. Open the Details tab and select DriverIds from the drop-down menu.
9. Copy and paste the first line into your browser.
10. Use the official hardware manufacturer’s drivers to find the right ones.
11. Both the LAN and WLAN drivers should be downloaded and installed.
12. Restart your computer and double-check your connection.

However, you can always use specialized software to download all outdated drivers to your PC automatically. They will choose and update the driver version that is most appropriate for your needs.

The tool recommended below is straightforward to use and effective, so you’ll receive the best results with minimal effort.

Practically, this method is excellent for easily managing your PC drivers since it allows you to install or update every driver you require in a matter of minutes.

The network drivers can then be updated and downloaded from an internet database that contains authentic manufacturer drivers.

There’s no reason not to take care of any prospective system difficulties by optimizing your gadgets to their total capacity.

4. Restart your TCP/IP stack

The TCP/IP stack is another option that has shown to be useful on several occasions. Resetting the TCP/IP stack, for example, can clear up any ambiguity in the system connection setup. Follow the comprehensive instructions below if you’re not familiar with this method.

1. Run the Command Prompt by right-clicking Start (Admin).
2. Type the following commands in the command line, pressing Enter after each one:
   • netsh int ip reset
   • netsh int tcp set heuristics disabled
   • netsh int tcp set global autotuninglevel=disabled
   • netsh int tcp set global rss=enabled
3. Restart your computer and try to connect again. If the issue persists, make sure to try the additional procedures listed below.

5. Temporarily disable Windows Firewall

Disabling Windows Firewall is a hazardous move, yet this stalwart protector of your PC might occasionally block your network for no apparent reason. So, turn it off for a while and see if things improve. Here’s how to turn off the Windows Firewall:

1. Activate the Control Panel.
2. Security and an open system
3. Select Windows Firewall from the drop-down menu.
4. From the left side, select Turn Windows Firewall on or off.
5. Confirm that Windows Firewall is turned off for both private and public networks.
6. Make an attempt to connect.

If the Windows Firewall isn’t the source of your connection problems, make sure it’s turned on.

6. Turn off the airplane mode

You should also check the Airplane mode. If you enable it by accident, it will block all connections. It’s also possible that the Creators Update activated it on its own. To turn off Airplane mode, follow these steps:

1. The Airplane mode symbol should be found in the Notification panel in the right corner of your desktop. If the icon isn’t present, there is another way to disable it.
2. Open the Settings menu.
3. Select Network & Internet from the drop-down menu.
4. Select Airplane mode from the drop-down menu.
5. Turn off the airplane mode.

Conclusion

I hope you found this guide useful. If you’ve got any questions or comments, don’t hesitate to use the shape below.

User Questions:

1. Why isn’t my Internet working now that Windows 10 has been updated?

The most common issues in Windows 11/10 can be resolved simply by restarting the machine. If your Internet stops working after an update, try restarting your computer to see if the problem has been resolved. Restarting your Router is another thing you should do.

2. After a Windows Update, you’re unable to connect to the server.

to repair If you get the error “We couldn’t connect to the update service,” do the following: Run the troubleshooter for Windows Update. Run the troubleshooter for Internet Connections. Start the Windows Update service again.

3. After installing Windows 10, how can I connect to Wi-Fi?

1. In the lower left corner, click the Windows Start button.
2. Make a selection of options.
3. Select Network & Internet from the drop-down menu. The Status window appears.
4. Select Network and Sharing Center from the drop-down menu. The second link from the bottom of the page is this one. The window for the Network and Sharing Center will appear.

4. Laptop won’t connect to internet after Windows 10 update?

Laptop won’t connect to internet after Windows 10 update? from techsupport

5. Cannot connect to internet after fresh install of Windows 10

Cannot connect to internet after fresh install of Windows 10 from pcmasterrace