Unable to Install Windows on Dynamic Disk Partition? Try This

Here we can see, “Unable to Install Windows on Dynamic Disk Partition? Try This”

You can run into the Windows cannot be installed on this hard disk space error when attempting to install Windows 10 on a dynamic disk. This problem happens because you must change the dynamic disk space into a basic disk before installing Windows.

The complete error message is as follows:

Windows cannot be installed to this hard disk space. The partition contains one or more dynamic volumes that are not supported for installation

As was previously said, several approaches have changed the dynamic disk to basic to fix this mistake.

Here are three solutions to fix the Windows that cannot be installed due to insufficient hard disk space error if you are also bothered by it.

How do I fix the Windows installation hard disk error?

1. Convert dynamic disk to basic using Disk Management tool

1. 1. To launch Run, press the Windows Key plus R.
   2. Open Disk Management by typing diskmgmt.msc and selecting OK.
   3. In Disk Management, the dynamic disk that needs to be converted will be seen.
   4. Select Delete Volume by right-clicking each volume on the dynamic disk.
   5. You will see the dynamic disk displayed as unallocated disk space once all its volumes have been erased.
   6. Convert to basic can be chosen by right-clicking the disk.
   7. Try installing Windows after the disk has been reduced to its basic state and look for any improvements.

Thanks to the built-in disk management tool, switching from a dynamic disk to a basic disk is simple. Nevertheless, the conversion process erases all of the disk’s data.

2. Convert dynamic disk to basic using Diskpart

1. 1. To launch Run, press the Windows Key plus R.
   2. To launch the Diskpart utility, enter diskpart and press OK.
      • To convert the disk, you must run a few instructions in the Command Prompt program.
   3. Enter the following command at the command prompt to list disks.
      • list disk
   4. To choose the disk you want to convert, type the following command. N is the disk number of the dynamic disk you want to convert in the command below.
      • select disk n
   5. Then type each of the following commands one at a time:
      • list volume
      • select volume m
        • m is the number of the volume on the dynamic disk
      • delete volume
        • Repeat the two commands select volume m and delete volume to delete all volumes
      • select disk n
      • convert basic
   6. Before deleting and converting the volume, ensure you have chosen the correct disk while running the command.

Since the partition contains one or more dynamic volumes that are not supported for installation, Windows cannot be installed on this disk space. Fortunately, this problem is relatively common and can be fixed by switching the dynamic disk over to basic.

3. Convert with a professional software

1. 1. Go to the official website and download AOMEI Partition Assistant.
   2. The AOMEI Partition Assistant should be installed and launched.
      • The utility will pick up the dynamic disk.
   3. Launch AOMEI Dynamic Disk Manager by clicking on it.
      • The AOMEI Dynamic Disk Manager will start up.
   4. Locate the dynamic disk you want to convert in the main interface.
   5. Convert to Basic Disk can be chosen by right-clicking the dynamic disk.
   6. To confirm the action, click OK.
   7. Re-enter the primary interface.
   8. To finish the procedure, click Commit and then Proceed.

The task may take the AOMEI Partition Assistant tool a few minutes to complete. After that, Windows can be installed on the disk without losing any data.

Although the Windows OS has a built-in disk management tool, the disk cannot be changed from dynamic to basic without erasing the data.

Conclusion

I hope you found this guide useful. If you’ve got any questions or comments, don’t hesitate to use the shape below.

User Questions

1. Can dynamic disk be used to install Windows?

Since the minimum drivers used by the Windows bootloader only allow the “Mirror” option, Windows only officially supports using dynamic disks for the system volume (before the OS is loaded).

2. What causes Windows to fail to install on this partition?

You must first halt the Windows installation process and restart the computer using the old OS disk. Installing EaseUS partition software will enable you to resolve the “Windows quickly cannot be installed to disk 0 partition 1” problem by converting MBR disks to GPT disks.

3. A dynamic disk might be able to boot.

You must include the disk containing the fundamental active boot and system partition in a dynamic disk group in order to make a boot and system partition dynamic. When you do that, the boot and system partition is immediately upgraded to an active dynamic simple volume, meaning the system will start from that volume.

4. Couldn’t install windows 10. Dynamic drive detected. Can’t …

Couldn’t install windows 10. Dynamic drive detected. Can’t remove EFI system reserved partition from techsupport

5. “Windows cannot be installed to this disk. The selected disk is …

"Windows cannot be installed to this disk. The selected disk is of the GPT partition style" Error when trying to install windows 7 64 bit. from windows